-
1 скорость износа деталей
Engineering: components wear rateУниверсальный русско-английский словарь > скорость износа деталей
-
2 как и в
•Again, step 1, the temperature is constant.
•As in wing theory, these components require an increase in blade angle.
•As with all other kinds of theories, the foremost criterion here is...
* * *Как и вThe results show first that, as in the Group 1 tests, the applied force does not appear to influence the wear rate.Clearly, in such cases, as well as in many others, a high precision feed-water flow rate measurement is of great value to the owner.Русско-английский научно-технический словарь переводчика > как и в
-
3 в отличие от
•Active current:alternating current that part in the phase with the voltage or the effective energy, as differentiated (or distinguished, or distinct) from the wattless or useless energy.
•The transistor is a current-controlled device as opposed to [or as distinct from, or in distinction to, or in contradistinction to, or in contrast to (or with), or as contrasted to, or unlike] the vacuum tube, which is a voltage-controlled device.
•The company has achieved a 200% increase in productivity by using the robot as opposed to manual servicing.
•The ultrasonic welding machine is semi-portable. By contrast, the resistance welder is a relatively cumbersome unit to move to a new location.
•Unlike copper windings, permanent magnets never wear out.
•These reactors are called light-water reactors to distinguish them from the type that uses heavy water.
•Contrary to the usual practice of...
•Sediments deposited by contour currents are called contourites, to set them apart from turbidites.
* * *В отличие от -- as opposed to, as contrasted to, as contrasted with; in contrast with, in contrast to; as distinct from, as distinguished from; unlike, unlike for; did not... as did, had not ... as had (британская конструкция)Most fine-pitch gears are used to transmit motion as opposed to the transmission of power. (В отличие от силовых передач большинство...)This possible separation regime appears to be of the ordinary type ( as contrasted to singular separation).Corrosion is brought about through chemical or electrochemical action, as contrasted with erosion caused by mechanical action.In contrast with the thicker inlet boundary layer, there is a pronounced thinning of the layer across the rotor.Also in contrast to the torsion mode, the critical phase angle always represented a backward wave.In this context the term "flooded bearing" becomes akin to "pressurized" bearing as distinct from Mr. G.'s classification where "flooded" is associated with bearings having no supply flow rate.The simplified turbine acceptance test, as distinguished from the full ASME turbine acceptance test, measures feedwater flow directly.Another advantage is that, unlike thermocouples, all components of this system including sensors are reusable.Unlike for torsion, the critical phase angle for the bending modes varied with sweep.Two weeks float is currently shown for these facilities compared to the rest of the 1A topside facilities (... показан двухнедельный плавающий срок...)Русско-английский научно-технический словарь переводчика > в отличие от
См. также в других словарях:
Wear — For other uses, see Wear (disambiguation). v · d · e Materials failure modes … Wikipedia
Components of jet engines — Diagram of a typical gas turbine jet engine. Air is compressed by the fan blades as it enters the engine, and it is mixed and burned with fuel in the combustion section. The hot exhaust gases provide forward thrust and turn the turbines which… … Wikipedia
Failure rate — is the frequency with which an engineered system or component fails, expressed for example in failures per hour. It is often denoted by the Greek letter λ (lambda) and is important in reliability engineering. The failure rate of a system usually… … Wikipedia
Electrical discharge machining — An electrical discharge machine Electric discharge machining (EDM), sometimes colloquially also referred to as spark machining, spark eroding, burning, die sinking or wire erosion,[1] is a manufacturing process whereby a desired shape is obtained … Wikipedia
Engine tuning — is the adjustment, modification or design of internal combustion engines to yield optimal performance, either in terms of power output or economy. It has a long history, almost as long as the development of the car in general, originating with… … Wikipedia
Tooth development — Radiograph of lower right (from left to right) third, second, and first molars in different stages of development. Tooth development or odontogenesis is the complex process by which teeth form from embryonic cells, grow, and erupt into the mouth … Wikipedia
Gas turbine — Microturbine redirects here. For turbines in electricity, see Small wind turbine. For turbines driven by the flow of gas, see Turbine. A typical axial flow gas turbine turbojet, the J85, sectioned for display. Flow is left to right, multistage… … Wikipedia
UTQG — Uniform Tire Quality Grading (UTQG)The National Highway Traffic Safety Administration (NHTSA) established the Uniform Tire Quality Grading Standards (UTQGS) in 49 CFR 575.104. Components The UTQG rating is made up of 3 components: Treadwear The… … Wikipedia
Chemical vapor deposition of diamond — Colorless gem cut from diamond grown by chemical vapor deposition Chemical vapor deposition of diamond or CVD is a method of producing synthetic diamond by creating the circumstances necessary for carbon atoms in a gas to settle on a substrate in … Wikipedia
Business and Industry Review — ▪ 1999 Introduction Overview Annual Average Rates of Growth of Manufacturing Output, 1980 97, Table Pattern of Output, 1994 97, Table Index Numbers of Production, Employment, and Productivity in Manufacturing Industries, Table (For Annual… … Universalium
materials science — the study of the characteristics and uses of various materials, as glass, plastics, and metals. [1960 65] * * * Study of the properties of solid materials and how those properties are determined by the material s composition and structure, both… … Universalium
